Product LibrarySystem Library
Site guideSign inCreate a free accountFree account
Specifications · Qatar

Specifications

DCP specifications, in order. Choose how your project is specified, CSI MasterFormat or NBS (NATSPEC is in preparation), then pick a Division and a section, or just type a product or a number. Not sure which section? Answer two questions ↓

CSI MasterFormat 2020Specify by CSI sectionThe North American system for ordering construction specifications: 50 Divisions, each section numbered, such as 07 14 16 Cold Fluid-Applied Waterproofing. Used on many projects in the Gulf and worldwide. Each DCP system comes with a three-part specification.Divisions 03 to 32 · 833 systems and productsShowing below ↓NBSSpecify by NBS work sectionThe UK National Building Specification, ordered by work section: a letter and a number, such as J30 Liquid applied tanking/damp proofing or M12 Trowelled resin flooring. Used where the consultant writes to UK practice.Work sections C to Z · the same DCP systems and productsOpen →
NATSPEC In preparationSpecify by NATSPEC worksectionThe Australian National Master Building Specification, ordered by worksections in workgroups, such as 06 Finish. Used where the consultant writes to Australian practice. DCP worksections are in preparation.In preparation · the same DCP systems and products

Compliance statements against QCS 2024, SBC and IS are in Compliance.

CSI MasterFormat 2020 Divisions

Division 03Concrete30 sections · 6 systems · 25 ARMOUR systems · 798 productsMaintenance of Concrete · Maintenance of Concrete Reinforcing · Maintenance of Cast-in-Place ConcreteOpen →Division 04Masonry3 sections · 18 productsMasonry Mortaring · Masonry Grouting · Masonry Control and Expansion JointsOpen →Division 05Metals1 section · 3 productsPost-Installed Concrete AnchorsOpen →Division 07Thermal and Moisture Protection28 sections · 14 systems · 146 ARMOUR systems · 248 productsDampproofing and Waterproofing · Dampproofing · Bituminous DampproofingOpen →Division 09Finishes10 sections · 41 systems · 10 ARMOUR systems · 252 productsCement Plastering · Tiling · Ceramic TilingOpen →Division 32Exterior Improvements1 section · 9 productsConcrete Paving Joint SealantsOpen →
Not sure which section?Answer two questions and we show what DCP has.Start again
1What are you specifying?
Waterproofing 401Flooring Systems 188Structural Strengthening 13Building Finishing Products 57Adhesives 46Concrete Admixtures 510Concrete Repair 71Grouts & Anchors 38Protective Coatings 42Sealants & Joints 55Surface Treatments 53Tile Adhesives & Grouts 96
2Which kind?
Accelerators & Antifreeze 54Air Entrainers & Foaming Agents 12Corrosion Inhibitors 2HRWR Plasticisers 90Hyperplasticisers 246Integral Waterproofing 24Mortar Plasticiser 3NRWR Plasticisers & Retarders 46Others 27Underwater Use Admixtures 6
3Where DCP has it (CSI sections)
03 24 00 Fibrous Reinforcing20 itemsOpen the section →03 05 00 Common Work Results for Concrete7 itemsOpen the section →
4What DCP has: 27 items
Blockadd CProductPrimary section · Not on the Qatar list: check supply with DCPUse: Blockadd C is used to improve workability, strength, surface finish and freeze/thaw cycle resistance properti…Concrete AdmixturesBS 4887Improving mortar plasticityOpen →Cem-Add AC100ProductPrimary sectionUse: Cem-Add AC100 is used in the formulation of glass reinforced concrete productsLiquid acrylic copolymer additive for GFRCGives a sprayable non-sag mixOpen →Cem-Add AC130ProductPrimary section · Not on the Qatar list: check supply with DCPUse: Cem-Add AC130 is used in the formulation of glass reinforced concrete productsPremium quality, high solids liquid acrylic copolymer additive for the GFRC production processCompressive strength ≥ 40 MPaGives a sprayable non-sag mixOpen →DonFiber PP MacroProductUse: DonFiber PP Macro is ideally designed for the followingHigh-performance macro polypropylene fibres for shotcreteTensile strength 640 MPaASTM C1116, EN 14889Reduces shotcrete reboundOpen →DonFiber PP Macro EProductUse: DonFiber PP Macro E is ideally designed for the followingHigh-performance corrugated macro polypropylene fibresTensile strength ≥ 450 MPaASTM C1116Rust-freeOpen →DonFiber PP Macro XProductUse: DonFiber PP Macro X is ideally designed for the followingHigh-performance macro polypropylene fibres for flooring applicationsTensile strength 560 - 650 MPaASTM C1116, EN 14889Rust-freeOpen →DonFiber PP UltraProductUse: DonFiber PP Ultra is ideally designed to decrease the plastic shrinkage cracking and plastic settlement crack…Ultra-fine, high performance monofilament polypropylene fibersElongation 20 - 25%ASTM C1116, EN 14889Reduces shotcrete reboundOpen →DonFiber PP-FProductUse: DonFiber PP-F is ideally designed for the followingHigh-performance fibrillated polypropylene fibersElongation 5.8 - 9.5%ASTM C1116, EN 14889Reduces shotcrete reboundOpen →DonFiber PP-F PlusProductNot on the Qatar list: check supply with DCPUse: DonFiber PP-F Plus is ideally designed for the followingHigh strength fibrillated polypropylene fibersElongation 10 - 12%ASTM C1116, EN 14889High tensile strengthOpen →DonFiber PP-MProductUse: DonFiber PP-M is ideally designed to decrease the plastic shrinkage cracking and plastic settlement cracking …High-performance monofilament polypropylene fibers (Formerly known as PP Fiber)Elongation 20 - 25%ASTM C1116, EN 14889Reduces shotcrete reboundOpen →DonFiber PP1000ProductUse: DonFiber PP1000 is ideally designed to reduce fire explosive spalling, decrease the plastic shrinkage crackin…Fire spalling resistance micro polypropylene fibersElongation 20 - 25%ASTM C1116, EN 14889Reduces shotcrete reboundOpen →DonFiber ST Type IProductNot on the Qatar list: check supply with DCPUse: DonFiber ST Type I (1.00 x 50 mm) is ideally designed for use in the following applications shotcreteHigh performance steel fibers with hooked ends for reinforcement of concrete and mortar (Formerly known as ST Fiber Type 1)ASTM A820, EN 14889-11 - 2 hours fire ratingOpen →DonFiber ST300ProductUse: DonFiber ST300 is ideally designed for use in the followingHigh performance corrugated steel fibers for reinforcement of concrete and mortarTensile strength of drawn wire 1100 - 1400 MPaASTM A820, EN 14889-1Open →DonPigmentProductPrimary section · Not on the Qatar list: check supply with DCPUse: DonPigment can be used to provide an aesthetic and colour appearance in the cement and concrete industry in d…High performance powder pigment with excellent tinting strengthExcellent tinting strengthOpen →Flocrete SR100ProductPrimary section · Not on the Qatar list: check supply with DCPUse: All kinds of cementitious materialsShrinkage reducing admixtureReduces alkali contentOpen →Flocrete VE10ProductPrimary sectionUse: Self compacting concreteHigh performance viscosity enhancer for self compacting concreteOptimises cement utilizationOpen →Flocrete VE25ProductPrimary sectionUse: Self compacting concreteHigh performance viscosity enhancer for self compacting concreteEN 934-2Optimises cement utilizationOpen →Macro PP FiberProductUse: Macro PP Fiber is ideally designed to decrease the plastic shrinkage cracking in the following applications s…High performance monofilaments polypropylene macro fiberASTM C1116, BS EN 14889-2High tensile strengthOpen →PP FiberProductUse: PP Fiber is ideally designed for use in the followingHigh performance fibrillated polypropylene fibersElongation 25 - 40%Rust freeOpen →PPF FiberProductNot on the Qatar list: check supply with DCPUse: PPF Fiber is ideally designed for use in the followingHigh performance fibrillated polypropylene fibersTensile strength 650 - 690 MPaRust freeOpen →Blockadd CProductAlso listed here · Not on the Qatar list: check supply with DCPUse: Blockadd C is used to improve workability, strength, surface finish and freeze/thaw cycle resistance properti…Concrete AdmixturesBS 4887Improving mortar plasticityOpen →Cem-Add AC100ProductAlso listed hereUse: Cem-Add AC100 is used in the formulation of glass reinforced concrete productsLiquid acrylic copolymer additive for GFRCGives a sprayable non-sag mixOpen →Cem-Add AC130ProductAlso listed here · Not on the Qatar list: check supply with DCPUse: Cem-Add AC130 is used in the formulation of glass reinforced concrete productsPremium quality, high solids liquid acrylic copolymer additive for the GFRC production processCompressive strength ≥ 40 MPaGives a sprayable non-sag mixOpen →DonPigmentProductAlso listed here · Not on the Qatar list: check supply with DCPUse: DonPigment can be used to provide an aesthetic and colour appearance in the cement and concrete industry in d…High performance powder pigment with excellent tinting strengthExcellent tinting strengthOpen →Flocrete SR100ProductAlso listed here · Not on the Qatar list: check supply with DCPUse: All kinds of cementitious materialsShrinkage reducing admixtureReduces alkali contentOpen →Flocrete VE10ProductAlso listed hereUse: Self compacting concreteHigh performance viscosity enhancer for self compacting concreteOptimises cement utilizationOpen →Flocrete VE25ProductAlso listed hereUse: Self compacting concreteHigh performance viscosity enhancer for self compacting concreteEN 934-2Optimises cement utilizationOpen →